PT-141 in 2026: a verification-first buying guide
For qualified researchers. Clarion Peptides products are sold for laboratory research use only. They are not for people or animals. This page is about checking a research material, not using one.
The short answer. Before you buy PT-141, ask for the lab report for that exact batch. A good report shows five things. The lab’s name is on it. The batch weighs what PT-141 should weigh. It says how pure the batch is, as a percent. The batch number on the report is the batch you get. And you can check the report with the lab itself, not only with the seller. The technical part of this page explains the numbers you will see on the report. If a seller cannot show you all five things before you pay, buy somewhere else.
What PT-141 is, in plain words
PT-141, also called bremelanotide, is a man-made peptide. A peptide is a short chain of amino acids, the same building blocks that make up proteins. This one is a short ring of 7. It comes as a freeze-dried powder in a small glass vial, kept frozen and dry. In a research catalog it is a reference material: a measured sample that a lab runs its tests against. Its ID number is CAS 189691-06-3. The formula, the exact weight, and the numbers a lab report should show are in the technical section below.
The five checks, in order (technical)
1. The laboratory is named on the certificate
“Third-party tested” names nobody. A real certificate of analysis names the laboratory that produced it, carries a report number, and the laboratory will confirm that number if you ask. If a vendor’s page says “independent lab” and stops there, stop there too. Two laboratories serve this segment with reports you can confirm directly: Janoshik Analytical, whose results are looked up by code at verify.janoshik.com, and Freedom Diagnostics Testing in Franklin, Tennessee, which publishes reports on its own database and will confirm a report number.
2. Identity by mass spectrometry, and the mass actually matches
PT-141’s formula is C50H68N14O10, its monoisotopic mass is 1,024.52 Da, and its average mass is 1,025.18 Da. A mass-spectrometry result proves the vial holds the molecule on the label, and the expected numbers are fixed by the formula, so you can check them without trusting anyone. A certificate usually reports the observed value at one of the common charge states:
- [M+H]+ near 1,025.53
- [M+2H]2+ near 513.27
- [M+3H]3+ near 342.52
The certificate should say which charge state and which mass (monoisotopic or average) it compares against, and the difference between observed and theoretical should be small and stated. A certificate that shows a mass with no charge state, or a mass that matches a different peptide, has not confirmed identity. Salt form matters for weight, not identity: acetate or TFA salt vials weigh a little more than the free peptide, which is why a good certificate separates identity, purity, and net content.
3. Purity by RP-HPLC, as a main-peak percentage with the method named
Purity answers a different question from identity: how much of what is in the vial is the target peptide. The number that holds up is the main-peak area from reverse-phase HPLC, stated as a percentage, with the method printed on the certificate. A “99%” that appears only in marketing copy is a claim. Clarion’s catalog specification is at least 99% by RP-HPLC, and the certificate for the specific lot is what proves it.
4. The lot code on the certificate is the lot code you receive
One certificate reused across every batch is a template, not a test. The lot code for the vials you would receive has to appear on the certificate, verbatim, and the vial size on the certificate should match the vial size you are buying. If a vendor cannot show you the certificate for the lot you would receive before you pay, you are buying blind.
5. You can authenticate the certificate with the laboratory, not the seller
This step takes the vendor out of the trust chain. Enter a Janoshik code at the lab’s own portal and compare; if the portal and the vendor’s copy disagree, the portal wins. A Freedom Diagnostics report lives on the laboratory’s own database, and the lab will confirm the report number. A vendor whose certificates exist only on the vendor’s own site has given you a PDF and nothing more.
Red flags specific to PT-141 listings
- A product page that describes effects or dosing instead of chemistry. That copy tells you what the seller wants to sell. It tells you nothing about what is in the vial.
- Purity quoted with no chromatogram and no named method.
- A certificate whose compound name or vial size does not match the listing (a 10 mg certificate on a 5 mg listing, or the reverse).
- No lot code anywhere on the page.
- A “verified” badge or QR code that lands on the vendor’s own page instead of a laboratory record.
Clarion’s current PT-141 lot, checked the same way
Read this the way you would read a competitor’s block, and check it against the laboratory rather than against us.
| Lot | P41, 10 mg vials. Our vial labels can’t be printed with a lot code, so a certificate card ships with the vials; its QR code opens this lot’s report. Product page: clarionpeptides.com/product/pt-141/ |
| Laboratory | Freedom Diagnostics Testing, Franklin, TN, named on the certificate. |
| Identity | Confirmed by LC-MS. The report shows [M+2H]2+ at 513.4 and the [M+H]+ signal near 1,025 to 1,026, against 513.27 and 1,025.53 expected for C50H68N14O10. |
| Purity | 99.83% main peak by RP-HPLC. |
| Authentication | The certificate is on the laboratory’s own database, not our server: coas.freedomdiagnosticstesting.com/Clar2607240044.pdf. The lot is also on the public Lot Ledger, and the walkthrough is at clarionpeptides.com/verify/. |
When lot P41 sells out, the product page and the ledger show the next lot with its own certificate. If the ledger says “testing in progress” for a lot, we claim no purity for it.
Every line of the P41 report, explained: PT-141 COA, line by line.
How Clarion compares with other vendors on these checks
We compared seven US research-peptide vendors, ourselves included, on whether they publish certificates, certify per lot, name the lab, allow lab-side authentication, and keep a public lot ledger. The method, the results, and the dataset are in Research Peptide Vendors Compared on Verification (2026). The general checklist for choosing any supplier is How to Choose a Research-Peptide Supplier.
Where to buy PT-141, in one line
Buy the lot whose certificate you confirmed with the laboratory before paying. If that is ours, the product page is linked above. If it is someone else’s, you still spent five minutes well.
All Clarion Peptides products are for laboratory research use only. Not for human or veterinary use. Nothing on this page is a claim about the effects of any compound.
